Fixed error 0199 – Security password retry count exceeded

by

Updated April 2025: Stop these error messages and fix common problems with this tool. Get it now at this link

  1. Download and install the software.
  2. It will scan your computer for problems.
  3. The tool will then fix the issues that were found.

error 0199 - Security password retry count exceeded

Errors caused by the computer BIOS are really dangerous and annoying. This is because such errors prevent the operating system from even booting up and throwing the error, even if it is suggested. One such error caused by the BIOS is error 0199, “System Security”, exceeding the number of attempts to enter the security password. Fixing these kinds of errors can be a bit tricky, but in the end, these solutions will at least get your operating system up and running. Below we take a look at some of the possible solutions to fix these errors.

Errors caused by your computer’s BIOS can get annoying because they are hard to fix. In fact, they are really dangerous and cannot be fixed with simple solutions. In fact, these types of errors don’t even allow the operating system to boot because they occur before you even get access to your computer. One such error is “Error 0199: System security – security password retry count exceeded”. Fixing this error can be quite difficult, but don’t worry as you will be guided through the process. Just follow the instructions below.

What leads to error 0199 – security password retry count exceeded

This particular error message appears when the hard drive password previously set in the BIOS is entered incorrectly three times in a row. The problem usually occurs on one of the following Lenovo models:

  • ThinkCentre M90 (all models).
  • ThinkCentre M90p (all models)
  • ThinkServer TS200v (all models)
  • ThinkStation E20 (all models)

Take Note: The error is not limited to these models. It can also occur with other Lenovo configurations.

The problem almost always occurs after a user enters the wrong supervisor password three times in a row (please).

Keep in mind that losing SVP is quite serious and may cause you to have to replace the motherboard.

However, if you manage to recover the SVP password, the steps to fix the Windows 0199 Security Password Retry Count Exceeded error are very simple.

If there is no way to recover the password, you can still bypass the error message, but you will need to open your computer (or laptop) case to manually reset the BIOS configuration.

Here are methods to help you bypass the “Windows Error 0199 Security Password Retry Count Exceeded” error, whether you have an SVP key or not. Just follow the method that applies to your specific situation and you will be able to solve the problem.

To fix error 0199 – Security Password Attempts Exceeded



Updated: April 2025

This tool is highly recommended to help you fix your error. Plus, this tool offers protection against file loss, malware, and hardware failures, and optimizes your device for maximum performance. If you already have a problem with your computer, this software can help you fix it and prevent other problems from recurring:

  • Step 1 : Install the PC Repair and Optimizer Tool. (Windows 10, 8, 7, XP, Vista).
  • Step 2 : Click Start Scan to determine what problems you are experiencing with your computer.
  • Step 3 : Click Repair Allto resolve all problems.

download



Restore the default BIOS settings

  1. Click the Setup button when the computer starts booting.
  2. The setup button is the F1 button in most cases for Lenovo computers. However, if the F1 button does not work, refer to your user manual.
  3. Please enter the key when the computer is protected.
  4. In the BIOS menu, press F9 to restore the default settings.
  5. When prompted to “Load Default Configuration Now”, select Yes.
  6. After loading the default configuration, press F10 to save your changes.
  7. Exit the BIOS.
  8. Reboot your computer. This should fix the error, and your computer will reboot normally with no problems.

Loading the default configuration in the BIOS can help eliminate the error of exceeding the number of repeated attempts to enter the Windows 0199 security password. However, you must know the security key for this to work.

Removing and reinstalling the CMOS battery

  1. Turn off your computer completely.
  2. Be sure to disconnect all cables, including the power cord.
  3. Open the case and locate the CMOS battery connected to the motherboard.
  4. Leave the motherboard in standby mode for a few minutes.
  5. Insert the CMOS battery pack.
  6. Connect the power cord and other cables to the computer.
  7. Reboot the computer and check if the error is corrected.

Perform a manual BIOS reset

  1. If the problem persists, try performing a manual BIOS reset.
  2. Completely shut down the computer by disconnecting the power cord and disconnecting other cables.
  3. Next, access the motherboard.
  4. Locate the BIOS configuration jumper on the motherboard.
  5. Move the jumper from pins 1, 2, and 3.
  6. Wait 20 seconds and then return the jumper to its original position.
  7. Reassemble the computer and restart the system.
  8. Your system should boot normally without error 0199, exceeded the number of security password retries.

The Windows error “0199 exceeded number of security password retries” can be easily fixed by resetting the default BIOS configuration.

However, if you have forgotten the password, you may have to remove the CMOS battery to reset the configuration, or manually reset the BIOS using a jumper.



APPROVED: To fix Windows errors, click here.



Frequently Asked Questions